doc & fix: 增加comtool plugin, 修改上传遥测长度问题

doc/HSJL 上位机串口通信协议.md

@@ -1,7 +1,7 @@
 # HSJL 上位机串口通信协议
 
 > 版本：v1.2
-> 日期：2025 年 6 月 12 日
+> 日期：2025 年 6 月 16 日
 
 ---
 
@@ -46,19 +46,19 @@ block-beta
 
 | 字段名     | 字节数 (Byte) | 说明 |
 |--|--|--|
-| 帧头       | 2 | 固定值：`0x54 0x5A` |
+| 帧头       | 2 | 固定值：`0x5A 0x54` |
 | 数据段    | ≤950 | 业务数据内容 |
 | Dummy Byte | 1 | 固定填充：`0x00` |
 | 校验和     | 1 | 所有**数据段**字节累加和（无符号累加） |
 | 数据段长度 | 2 | 数据段字节数（不含 Dummy/校验/帧尾） |
-| 帧尾       | 2 | 固定值：`0xFE 0x5A` |
+| 帧尾       | 2 | 固定值：`0x5A 0xFE` |
 
 ### 帧内冲突规避规则
 
-为防止数据段中出现帧尾 `0xFE 0x5A`：
+为防止数据段中出现帧尾 `0x5A 0xFE`：
 
-- 若数据段中出现 `0xFE 0x5A`，需插入 `0x00` 变成 `0x00 0xFE 0x5A`
+- 若数据段中出现 `0x5A 0xFE`，需插入 `0x00` 变成 `0x00 0x5A 0xFE`
-- 接收端收到 `0x00 0xFE 0x5A` 还原为 `0xFE 0x5A`
+- 接收端收到 `0x00 0x5A 0xFE` 还原为 `0x5A 0xFE`
 
 ### 帧长说明
 
@@ -192,13 +192,13 @@ block-beta
 
 ### （可选）遥测指令
 
-遥测指令上传的 Payload 由 5 部分组成，顺序存储，共 188 字节：
+遥测指令上传的 Payload 由 5 部分组成，顺序存储，共 200 字节：
 
 | 字段名       | 字节数 (Byte) |
 | ------------ | ------------- |
 | 时间戳       | 8             |
 | 总线日志     | 16            |
-| 链路层日志   | 88            |
+| 链路层日志   | 100           |
 | 物理层日志   | 56            |
 | 硬件状态日志 | 20            |
 
@@ -219,7 +219,7 @@ block-beta
 
 #### 链路层日志
 
-链路层日志顺序存储，共 88字节：
+链路层日志顺序存储，共 100 字节：
 
 | 字段名               | 字节数 (Byte) | 说明                                     |
 | -------------------- | ------------- | ---------------------------------------- |
@@ -239,12 +239,15 @@ block-beta
 | 分发帧发送计数器     | 4             | 每发送一次分发帧，计数器+1（仅簇首）     |
 | 分发帧接收计数器     | 4             | 每配置接收一次分发帧，计数器+1（仅成员） |
 | 分发帧接收正确计数器 | 4             | 每正确接收一次分发帧，计数器+1（仅成员） |
-| 网关帧发送计数器     | 4             | 每发送一次网关帧，计数器+1               |
+| 网管帧发送计数器     | 4             | 每发送一次网管帧，计数器+1               |
-| 网关帧接收计数器     | 4             | 每配置接收一次网关帧，计数器+1           |
+| 网管帧接收计数器     | 4             | 每配置接收一次网管帧，计数器+1           |
-| 网关帧接收正确计数器 | 4             | 每正确接收一次网关帧，计数器+1           |
+| 网管帧接收正确计数器 | 4             | 每正确接收一次网管帧，计数器+1           |
 | RTT帧发送计数器      | 4             | 每发送一次 RTT 帧，计数器+1              |
 | RTT帧接收计数器      | 4             | 每配置接收一次 RTT 帧，计数器+1          |
 | RTT帧接收正确计数器  | 4             | 每正确接收一次 RTT 帧，计数器+1          |
+| 业务帧发送计数器     | 4             | 每发送一次业务帧，计数器+1               |
+| 业务帧接收计数器     | 4             | 每配置接收一次业务帧，计数器+1           |
+| 业务帧接收正确计数器 | 4             | 每正确接收一次业务帧，计数器+1           |
 | 时间偏移量记录       | 4, int32      | 记录上一次节点时间和帧同步时间的偏差     |
 | 发送数据ID记录       | 4             | 记录上一次发送数据的ID                   |
 | 接收数据ID记录       | 4             | 记录上一次接收数据的ID                   |

doc/comtool-plugin-hsjl.py

@@ -0,0 +1,433 @@
+'''
+    @brief This is an example plugin, can receive and send data
+    @author
+    @date
+    @license LGPL-3.0
+'''
+from PyQt5.QtWidgets import QWidget, QVBoxLayout, QHBoxLayout, QTextEdit, QPushButton, QLabel, QScrollArea, QSplitter
+from PyQt5.QtCore import Qt, pyqtSignal
+from PyQt5.QtGui import QFont, QTextCursor
+from struct import Struct
+try:
+    import utils_ui
+    from plugins.base import Plugin_Base
+    from conn import ConnectionStatus
+    from i18n import _
+    from widgets import statusBar
+except ImportError:
+    from COMTool import utils_ui
+    from COMTool.plugins.base import Plugin_Base
+    from COMTool.i18n import _
+    from COMTool.conn import  ConnectionStatus
+    from COMTool.widgets import statusBar
+
+class Plugin(Plugin_Base):
+    id = "HJ DATALINK"
+    name = _("HJ DATALINK")
+    showReceiveDataSignal = pyqtSignal(str)
+
+    def onInit(self, config):
+        '''
+            init params
+        '''
+        default = {
+            "version": 1,
+            "customSendItems": [
+                {
+                    "caption": "自检",
+                    "icon": "fa5.question-circle",
+                    "data": "5A 54 E1 EE 00 CF 02 5A FE"
+                },
+                # {
+                #     "caption": "数据发送测试 - 1",
+                #     "icon": "fa5.play-circle",
+                #     "data": ""
+                # },
+                # {
+                #     "caption": "数据发送测试 - 2",
+                #     "icon": "fa5.play-circle",
+                #     "data": ""
+                # },
+                {
+                    "caption": "装订 - 【主 - 0x01】128 kbps，时隙表 0",
+                    "icon": "fa5.play-circle",
+                    "data": "5A 54 E3 EE AA 01 22 00 00 7B 06 5A FE"
+                },
+                {
+                    "caption": "装订 - 【主 - 0x01】2 Mbps，时隙表 1",
+                    "icon": "fa5.play-circle",
+                    "data": "5A 54 E3 EE AA 01 44 01 00 C1 06 5A FE"
+                },
+                {
+                    "caption": "装订 - 【主 - 0x01】静默",
+                    "icon": "fa5.play-circle",
+                    "data": "5A 54 E3 EE 55 01 22 00 00 49 06 5A FE"
+                },
+                {
+                    "caption": "装订 - 【从 - 0x02】128 kbps，时隙表 0",
+                    "icon": "fa5.play-circle",
+                    "data": "5A 54 E3 EE AA 02 22 00 00 9F 06 5A FE"
+                },
+                {
+                    "caption": "装订 - 【从 - 0x02】2 Mbps，时隙表 1",
+                    "icon": "fa5.play-circle",
+                    "data": "5A 54 E3 EE AA 02 44 01 00 C2 06 5A FE"
+                },
+                {
+                    "caption": "装订 - 【从 - 0x02】静默",
+                    "icon": "fa5.play-circle",
+                    "data": "5A 54 E3 EE 55 02 22 00 00 0C 06 5A FE"
+                },
+                {
+                    "caption": "装订 - 【从 - 0x03】128 kbps，时隙表 0",
+                    "icon": "fa5.play-circle",
+                    "data": "5A 54 E3 EE AA 03 22 00 00 A0 06 5A FE"
+                },
+                {
+                    "caption": "装订 - 【从 - 0x03】2 Mbps，时隙表 1",
+                    "icon": "fa5.play-circle",
+                    "data": "5A 54 E3 EE AA 03 44 01 00 C3 06 5A FE"
+                },
+                {
+                    "caption": "装订 - 【从 - 0x03】静默",
+                    "icon": "fa5.play-circle",
+                    "data": "5A 54 E3 EE 55 03 22 00 00 0D 06 5A FE"
+                },
+                {
+                    "caption": "遥测",
+                    "icon": "fa5.play-circle",
+                    "data": "5A 54 E6 EE 00 D4 02 5A FE"
+                },
+            ]
+        }
+        self.config = config
+        for k in default:
+            if not k in self.config:
+                self.config[k] = default[k]
+
+    def onConnChanged(self, status:ConnectionStatus, msg:str):
+        print("-- connection changed: {}, msg: {}".format(status, msg))
+
+    def onWidgetMain(self, parent):
+        '''
+            main widget, just return a QWidget object
+        '''
+        self.mainWidget = QSplitter(Qt.Vertical)
+        # receive widget
+        self.receiveWidget = QTextEdit("")
+        font = QFont('Consolas, DejaVu Sans Mono, Courier New, monospace, Microsoft YaHei', 10)
+        self.receiveWidget.setFont(font)
+        self.receiveWidget.setLineWrapMode(QTextEdit.NoWrap)
+        # clear button
+        self.clearBtn = QPushButton("")
+        utils_ui.setButtonIcon(self.clearBtn, "mdi6.broom")
+        # send scroll
+        self.customSendScroll = QScrollArea()
+        self.customSendScroll.setMinimumHeight(20)
+        self.customSendScroll.setWidgetResizable(True)
+        self.customSendScroll.setVerticalScrollBarPolicy(Qt.ScrollBarAsNeeded)
+        self.customSendScroll.setHorizontalScrollBarPolicy(Qt.ScrollBarAlwaysOff)
+        cutomSendItemsWraper = QWidget()
+        self.customSendScroll.setWidget(cutomSendItemsWraper)
+
+        # -- wrapper widget
+        cutomSendItemsWraper0 = QWidget()
+        cutomSendItemsWraper0.setProperty("class", "scrollbar2")
+        layout0 = QVBoxLayout()
+        layout0.setContentsMargins(0,8,0,0)
+        cutomSendItemsWraper0.setLayout(layout0)
+        layout0.addWidget(self.customSendScroll)
+        customSendItemsLayoutWrapper = QVBoxLayout()
+        customSendItemsLayoutWrapper.setContentsMargins(0,0,0,0)
+        cutomSendItemsWraper.setLayout(customSendItemsLayoutWrapper)
+
+        # -- items container
+        self.customItems = QWidget()
+        self.customSendItemsLayout = QVBoxLayout()
+        self.customSendItemsLayout.setContentsMargins(0,0,0,0)
+        self.customItems.setLayout(self.customSendItemsLayout)
+        customSendItemsLayoutWrapper.addWidget(self.customItems)
+        customSendItemsLayoutWrapper.addStretch(0)
+
+        # add widgets
+        self.mainWidget.addWidget(self.receiveWidget)
+        self.mainWidget.addWidget(self.clearBtn)
+        self.mainWidget.addWidget(cutomSendItemsWraper0)
+        self.mainWidget.setStretchFactor(0, 2)
+        self.mainWidget.setStretchFactor(1, 1)
+        self.mainWidget.setStretchFactor(2, 11)
+
+        # event
+        def clearReceived():
+            self.receiveWidget.clear();self.statusBar.clear()
+        self.clearBtn.clicked.connect(clearReceived)
+        return self.mainWidget
+
+    def onWidgetStatusBar(self, parent):
+        self.statusBar = statusBar(rxTxCount=True)
+        return self.statusBar
+
+    def onUiInitDone(self):
+        '''
+            UI init done, you can update your widget here
+            this method runs in UI thread, do not block too long
+        '''
+        newItems = []
+        print(self.config["customSendItems"])
+        for item in self.config["customSendItems"]:
+            print(item)
+            item = self.insertSendItem(item, load=True)
+            newItems.append(item)
+        self.config["customSendItems"] = newItems
+        self.showReceiveDataSignal.connect(self.showReceivedData)
+        # frame struct
+        self.structSelfTestRsp = Struct("<BB B BBBbbb HHHBBbB B 3s")
+        self.structStatusCheckRsp = Struct("<BB Q    IIII    IBBBBIB III III III III III i II 3s    IIII d Q dBB dB H B 2s    BBBbbb HHHBBbB B 3s")
+        self.structFljData = Struct("<dddd IHI fff fff")
+        self.structLjData = Struct("<IHI ffff IHI fff fff fff IHI fff fff fff IHI fff fff fff I")
+        self.structSysInfo = Struct("<IHI H B I B fff fff fff")
+
+    def insertSendItem(self, item = None, load = False):
+        caption = item["caption"]
+        itemWidget = QWidget()
+        layout = QHBoxLayout()
+        layout.setContentsMargins(0,0,0,0)
+        itemWidget.setLayout(layout)
+        send = QPushButton("")
+        label = QLabel(caption)
+        if (not "icon" in item) or not item["icon"]:
+            item["icon"] = "fa.send"
+        utils_ui.setButtonIcon(send, item["icon"])
+        send.setProperty("class", "smallBtn")
+        def sendCustomData(idx):
+            self.sendCustomItem(self.config["customSendItems"][idx])
+        send.clicked.connect(lambda: sendCustomData(self.customSendItemsLayout.indexOf(itemWidget)))
+        layout.addWidget(label)
+        layout.addWidget(send)
+        self.customSendItemsLayout.addWidget(itemWidget)
+        if not load:
+            self.config["customSendItems"].append(item)
+        return item
+
+    def showReceivedData(self, text: str):
+        curScrollValue = self.receiveWidget.verticalScrollBar().value()
+        self.receiveWidget.moveCursor(QTextCursor.End)
+        endScrollValue = self.receiveWidget.verticalScrollBar().value()
+        self.receiveWidget.insertPlainText(text)
+        if curScrollValue < endScrollValue:
+            self.receiveWidget.verticalScrollBar().setValue(curScrollValue)
+        else:
+            self.receiveWidget.moveCursor(QTextCursor.End)
+
+    def onReceived(self, data : bytes):
+        '''
+            call in receive thread, not UI thread
+        '''
+        self.statusBar.addRx(len(data))
+        ## Apply data validation check
+        if len(data) < 7:
+            self.showReceiveDataSignal.emit("\n### Wrong data format: wrong frame header/tail\n")
+            return
+
+        dataLen = data[-3]
+        if data[0] != 0x5A or data[1] != 0x54 or data[-1] != 0xFE or data[-2] != 0x5A:
+            self.showReceiveDataSignal.emit("\n### Wrong data format: wrong length\n")
+
+        checkSum = 0
+        for i in data[2:-4]:
+            checkSum += i
+        if checkSum & 0xFF != data[-4]:
+            self.showReceiveDataSignal.emit("\n### Wrong data format: wrong check sum\n")
+
+        ## Eval data
+        data = data[2:-5].replace(b'\x00\x54\xFE', b'\x54\xFE')
+        # self.printFrame(data)
+        if data[0] == 0xE1:
+            # eval self test
+            self.showReceiveDataSignal.emit(self.evalSelfTestRsp(data) + "\n")
+        elif data[0] == 0xE6 or data[0] == 0xF6:
+            self.showReceiveDataSignal.emit(self.evalStatusCheckRsp(data) + "\n")
+        elif data[0] == 0xE5 or data[0] == 0xF5:
+            self.showReceiveDataSignal.emit('Retrieved Data Frame:\n' + self.printFrame(data) + "\n")
+        else:
+            self.showReceiveDataSignal.emit(f"\n### Unexpected response code 0x{data[0]:02x}.\n")
+
+    def evalSelfTestRsp(self, data: bytes):
+        try:
+            payload = self.structSelfTestRsp.unpack(data)
+        except :
+            return f"\n### evalSelfTestRsp:: Failed to unpack data (data length {len(data)} byte).\n"
+
+        ret = "----------- 自检回令 -----------\n"
+
+        ret += f"节点编号: 0x{payload[-2]:02X}\n"
+
+        ret += "节点类型: "
+        if payload[1] == 0xEE:
+            ret += f"C频段 (0x{payload[1]:02X})\n"
+        else:
+            ret += f"【未知错误】(0x{payload[1]:02X})\n"
+
+        ret += "自检结果: "
+        if payload[2] == 0xAA:
+            ret += f"正常 (0x{payload[2]:02X})\n"
+        elif payload[2] == 0x55:
+            ret += f"异常 (0x{payload[2]:02X})\n"
+        else:
+            ret += f"【未知错误】(0x{payload[2]:02X})\n"
+
+        hwOffset = 3
+
+        ret += f"FPGA 电压监测: {bin(payload[hwOffset+0])[2:].zfill(8)}\n"
+        ret += f"时钟锁定状态:   {bin(payload[hwOffset+1])[2:].zfill(8)}\n"
+        ret += f"AD 锁定状态:   {bin(payload[hwOffset+2])[2:].zfill(8)}\n"
+        ret += f"AD 温度 1: {payload[hwOffset+3]:>4d}\n"
+        ret += f"AD 温度 2: {payload[hwOffset+4]:>4d}\n"
+        ret += f"FPGA 温度: {payload[hwOffset+5]:>4d}\n"
+        ret += f"天线-1 工作 PLL: {(payload[hwOffset+6] >> 15) & 0x01:>1d}\n"
+        ret += f"天线-1 工作频率: {(payload[hwOffset+6] & 0x7FFF)+3700:>4d}\n"
+        ret += f"天线-2 工作 PLL: {(payload[hwOffset+7] >> 15) & 0x01:>1d}\n"
+        ret += f"天线-2 工作频率: {(payload[hwOffset+7] & 0x7FFF)+3700:>4d}\n"
+        ret += f"天线-3 工作 PLL: {(payload[hwOffset+8] >> 15) & 0x01:>1d}\n"
+        ret += f"天线-3 工作频率: {(payload[hwOffset+8] & 0x7FFF)+3700:>4d}\n"
+        ret += f"天线 PLL 锁定状态: {bin(payload[hwOffset+9])[2:].zfill(8)}\n"
+        ret += f"天线工作模式: {bin(payload[hwOffset+10])[2:].zfill(8)}\n"
+        ret += f"天线温度: {payload[hwOffset+11]:>4d}\n"
+        ret += "--------------------------------\n"
+
+        return ret + '\n' + self.printFrame(data)
+
+    def printFrame(self, data: bytes):
+        ret = ''
+        for i in range(len(data)):
+            ret += f'{data[i]:02X}'
+            ret += '\n' if i%16 == 15 else ' '
+        ret += '\n'
+        return ret
+
+    def evalStatusCheckRsp(self, data: bytes):
+        try:
+            payload = self.structStatusCheckRsp.unpack(data)
+        except :
+            return f"\n### evalStatusCheckRsp:: Failed to unpack data (data length {len(data)} byte).\n"
+
+        ret = "----------- 遥测回令 -----------\n"
+
+        ret += "节点类型: "
+        if payload[1] == 0xEE:
+            ret += f"C频段 (0x{payload[1]:02X})\n"
+        else:
+            ret += f"【未知错误】(0x{payload[1]:02X})\n"
+
+        ret += f"时间戳: {payload[2]/1e5:.2f} ms\n"
+
+        sysbusOffset = 3
+        linkOffset = 7
+        phyOffset = 36
+        hwOffset = 47
+
+        ret += "\n  -- 总线状态\n"
+        ret += f"配置装订:    {payload[sysbusOffset + 0]:08X}\n"
+        ret += f"接收数据计数: {payload[sysbusOffset + 1]:>6d}\n"
+        ret += f"发送数据计数: {payload[sysbusOffset + 2]:>6d}\n"
+        ret += f"遥测请求计数: {payload[sysbusOffset + 3]:>6d}\n"
+
+        ret += "\n  -- 链路层状态\n"
+        ret += f"时元号: {payload[linkOffset + 0]:>6d}\n"
+        ret += f"时隙号: {payload[linkOffset + 1]:>3d}\n"
+
+        ret += "当前角色: "
+        if payload[linkOffset + 2] == 0xAA:
+            ret += f"簇首 (0x{payload[linkOffset + 2]:02X})\n"
+        elif payload[linkOffset + 2] == 0xCC:
+            ret += f"成员 (0x{payload[linkOffset + 2]:02X})\n"
+        else:
+            ret += f"【未知错误】(0x{payload[linkOffset + 2]:02X})\n"
+
+        ret += "网络连接状态: "
+        if payload[linkOffset + 3] == 0x11:
+            ret += f"已连接 (0x{payload[linkOffset + 3]:02X})\n"
+        elif payload[linkOffset + 3] == 0x00:
+            ret += f"未连接 (0x{payload[linkOffset + 3]:02X})\n"
+        else:
+            ret += f"【未知错误】(0x{payload[linkOffset + 3]:02X})\n"
+
+        ret += "网络运行阶段: "
+        if payload[linkOffset + 4] == 0x11:
+            ret += f"建网阶段 (0x{payload[linkOffset + 4]:02X})\n"
+        elif payload[linkOffset + 4] == 0x22:
+            ret += f"业务通信 (0x{payload[linkOffset + 4]:02X})\n"
+        else:
+            ret += f"【未知错误】(0x{payload[linkOffset + 4]:02X})\n"
+
+        ret += f"重建/入网计数: {payload[linkOffset + 5]:>6d}\n"
+        ret += f"通信天线位号:  {payload[linkOffset + 6]:>1d}\n"
+
+        ret += f"建网帧发送计数: {payload[linkOffset + 7]:>6d}\n"
+        ret += f"建网帧接收计数: {payload[linkOffset + 8]:>6d}\n"
+        ret += f"建网帧正确计数: {payload[linkOffset + 9]:>6d}\n"
+        ret += f"应答帧发送计数: {payload[linkOffset + 10]:>6d}\n"
+        ret += f"应答帧接收计数: {payload[linkOffset + 11]:>6d}\n"
+        ret += f"应答帧正确计数: {payload[linkOffset + 12]:>6d}\n"
+        ret += f"分发帧发送计数: {payload[linkOffset + 13]:>6d}\n"
+        ret += f"分发帧接收计数: {payload[linkOffset + 14]:>6d}\n"
+        ret += f"分发帧正确计数: {payload[linkOffset + 15]:>6d}\n"
+        ret += f"网管帧发送计数: {payload[linkOffset + 16]:>6d}\n"
+        ret += f"网管帧接收计数: {payload[linkOffset + 17]:>6d}\n"
+        ret += f"网管帧正确计数: {payload[linkOffset + 18]:>6d}\n"
+        ret += f"RTT 帧发送计数: {payload[linkOffset + 19]:>6d}\n"
+        ret += f"RTT 帧接收计数: {payload[linkOffset + 20]:>6d}\n"
+        ret += f"RTT 帧正确计数: {payload[linkOffset + 21]:>6d}\n"
+        ret += f"业务帧发送计数: {payload[linkOffset + 22]:>6d}\n"
+        ret += f"业务帧接收计数: {payload[linkOffset + 23]:>6d}\n"
+        ret += f"业务帧正确计数: {payload[linkOffset + 24]:>6d}\n"
+        ret += f"时间偏差记录: {payload[linkOffset + 25]/1e2:.2f} us\n"
+        ret += f"发送数据 ID: {payload[linkOffset + 26]:>6d}\n"
+        ret += f"接收数据 ID: {payload[linkOffset + 27]:>6d}\n"
+
+        ret += "\n  -- 物理层状态\n"
+        ret += f"捕获计数:    {payload[phyOffset + 0]:>6d}\n"
+        ret += f"帧同步计数:  {payload[phyOffset + 1]:>6d}\n"
+        ret += f"译码计数:    {payload[phyOffset + 2]:>6d}\n"
+        ret += f"CRC 正确计数:{payload[phyOffset + 3]:>6d}\n"
+        ret += f"多普勒估计:  {payload[phyOffset + 4]:.2f} Hz\n"
+        ret += f"正确接收时刻: {payload[phyOffset + 5]/1e2:.2f} us\n"
+        ret += f"捕获峰均比:  {payload[phyOffset + 6]:.2f}\n"
+        ret += f"捕获相位值:  {payload[phyOffset + 7]:>3d}\n"
+        ret += f"捕获频偏通道: {payload[phyOffset + 8]:>3d}\n"
+        ret += f"帧同步峰均比:   {payload[phyOffset + 9]:.2f}\n"
+        ret += f"帧同步频偏通道: {payload[phyOffset + 10]:>3d}\n"
+        ret += f"交织输入数据幅度统计:\t0x{payload[phyOffset + 11]:04X}\n"
+        ret += f"天线控制模式: {bin(payload[phyOffset + 10])[2:].zfill(8)}\n"
+
+        ret += "\n  -- 硬件状态\n"
+        ret += f"FPGA 电压监测: {bin(payload[hwOffset+0])[2:].zfill(8)}\n"
+        ret += f"时钟锁定状态:   {bin(payload[hwOffset+1])[2:].zfill(8)}\n"
+        ret += f"AD 锁定状态:   {bin(payload[hwOffset+2])[2:].zfill(8)}\n"
+        ret += f"AD 温度 1: {payload[hwOffset+3]:>4d}\n"
+        ret += f"AD 温度 2: {payload[hwOffset+4]:>4d}\n"
+        ret += f"FPGA 温度: {payload[hwOffset+5]:>4d}\n"
+        ret += f"天线-1 工作 PLL: {(payload[hwOffset+6] >> 15) & 0x01:>1d}\n"
+        ret += f"天线-1 工作频率: {(payload[hwOffset+6] & 0x7FFF)+3700:>4d}\n"
+        ret += f"天线-2 工作 PLL: {(payload[hwOffset+7] >> 15) & 0x01:>1d}\n"
+        ret += f"天线-2 工作频率: {(payload[hwOffset+7] & 0x7FFF)+3700:>4d}\n"
+        ret += f"天线-3 工作 PLL: {(payload[hwOffset+8] >> 15) & 0x01:>1d}\n"
+        ret += f"天线-3 工作频率: {(payload[hwOffset+8] & 0x7FFF)+3700:>4d}\n"
+        ret += f"天线 PLL 锁定状态: {bin(payload[hwOffset+9])[2:].zfill(8)}\n"
+        ret += f"天线工作模式: {bin(payload[hwOffset+10])[2:].zfill(8)}\n"
+        ret += f"天线温度: {payload[hwOffset+11]:>4d}\n"
+
+        ret += "--------------------------------\n"
+        return ret + '\n' + self.printFrame(data)
+
+    def onSent(self, ok, msg, length, path):
+        if ok:
+            self.statusBar.addTx(length)
+        else:
+            self.hintSignal.emit("error", _("Error"), _("Send data failed!") + " " + msg)
+
+    def sendCustomItem(self, item):
+        data = item["data"]
+        dateBytes = self.parseSendData(data, encoding = self.configGlobal["encoding"], isHexStr = True)
+        if dateBytes:
+            self.send(dateBytes, callback=self.onSent)

src/systembus/systembus.c

@@ -128,7 +128,7 @@
 // -- Request
 // -- -- --
 // -- Response
-#define RM_TEST_RSP_LEN 190
+#define RM_TEST_RSP_LEN 202
 // -- -- 8 byte time stamp
 #define RT_TIME_STAMP_OFFSET 0x02
 #define RT_TIME_STAMP_LEN 8
@@ -137,12 +137,12 @@
 #define RT_SYSBUS_LOG_LEN 16
 // -- -- 88 byte link layer log
 #define RT_LINK_LOG_OFFSET 0x1A
-#define RT_LINK_LOG_LEN 88
+#define RT_LINK_LOG_LEN 100
 // -- -- 56 byte physical layer log
-#define RT_PHY_LOG_OFFSET 0x72
+#define RT_PHY_LOG_OFFSET 0x7E
 #define RT_PHY_LOG_LEN 56
 // -- -- 20 byte hardware log
-#define RT_HARDWARE_ST_OFFSET 0xAA
+#define RT_HARDWARE_ST_OFFSET 0xB6
 #define RT_HARDWARE_ST_LEN 20
 
 // My Production Type